CISCIO NEW UPDATED: New Updated 350-080 Exam Questions from Braindump2go 350-080 PDF Dumps and 350-080 VCE Dumps! Welcome to Download the Newest Braindump2go 350-080 VCE&PDF Dumps: http://www.braindump2go.com/350-080.html (394 Q&As)

Do you want to pass Cisco 350-080 Exam ? If you answered YES, then look no further. Braindump2go offers you the best 350-080 exam questions which cover all core test topics and certification requirements.All REAL questions and answers from Cisco Exam Center will help you be a 350-080 certified!

350-080 Dumps,350-080 Exam Dumps,350-080 Brainfump,350-080 Questions,350-080 VCE,350-080 PDF,350-080 Actual Test,350-080 Study Guide,350-080 Book,350-080 CCIE Data Center Written Exam,350-080 Test

QUESTION 81
When using VSD, traffic flow goes from the virtual machine to which of these?

A.    Upstream switch
B.    Virtual Supervisor Module
C.    VMware distributed switch
D.    VMware vSwitch
E.    Service virtual machine

Answer: E

QUESTION 82
Given the following configuration, what command can be used to determine the physical path that traffic will be sent out upon?
Port-profile type Ethernet name vm-data
Switchport mode trunk
Switchport trunk allowed vlan 200-210
Channel-group auto mode on mac-pinning
State enabled
Vmware port-group
No shut
Port-profile type vethernet name vlan-200
Switchport mode access
Switchport vlan 200
State enabled
Vmware port-group
No shut

A.    module vem X execute vemcmd show trunk
B.    show module 3 internal pinning
C.    module vem X execute vemcmd show port
D.    show module vem mapping
E.    show interface vethX pinning

Answer: C

QUESTION 83
What are the four vPath packet flow steps? (Choose four.)

A.    perform flow lookups
B.    intercept packets on service enabled ports
C.    run packets through the vPath flow manager
D.    classify the packets
E.    flow manager emits an action for the packets
F.    enforce the action determined by the flow manager

Answer: BCEF

QUESTION 84
Refer to the exhibit. Your company requires a Cisco UCS configuration that will, at a minimum, allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement? (Choose three.)

A.    Cisco UCS 6148, Cisco UCS 6248UP, or the Cisco UCS 6296UP fabric interconnects
B.    Cisco UCS 2104XP Fabric Extender
C.    Cisco UCS 2204XP or 2208XP Fabric Extenders
D.    Cisco UCS M81KR Virtual Interface Card
E.    Cisco UCS Virtual Interface Card 1280
F.    Cisco UCS Virtual Interface Card 1240 with a port expander

Answer: AEF

QUESTION 85
A Cisco switch has this configuration for a port channel connecting to an ESXi using dual NICs and is intended for use with an N1Kv.
Interface fastethernet 1/10
Switchport mode trunk
Switchport trunk allowed vlan all
Channel-group 10 mode on
No shut
Interface fastethernet 1/11
Switchport mode trunk
Switchport trunk allowed vlan all
Channel-group 10 mode on
No shut
Interface port-channel10
Switchport mode trunk
Switchport allowed vlan all
No shut
Which Port Channel configuration must be used on the Nexus 1000v port-profile?

A.    MAC pinning
B.    Cisco Discovery Protocol pinning
C.    Mode On
D.    Mode Active
E.    No port channel configuration

Answer: C

QUESTION 86
Refer to the exhibit. According to the equipment tab in Cisco UCS Manager, which is true?

A.    A is an uplink port, B is a fabric port, C is a server port, D is a backplane port, E is a DCE interface,
and F is a vNIC
B.    A is an uplink port, B is a server port, C is a fabric port, D is a backplane port, E is a DCE interface,
and F is a vNIC
C.    A is an uplink port, B is a fabric port, C is a backplane port, D is a server port, E is a DCE interface,
and F is a vNIC
D.    A is an uplink port, B is a server port, C is a fabric port, D is a DCE interface, E is a backplane port,
and F is a vNIC
E.    A is an fabric port, B is a downlink port, C is an uplink port, D is a server port, E is a VIC interface,
and F is a vNIC

Answer: B

QUESTION 87
Refer to the exhibit. The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B (Path C). Which actions might be used to change this behavior?

A.    Fix the port channel configuration between Fabric Interconnect B and Nexus 5548 B as the port
channel IDs do not match.
B.    Modify the bridge priority on the fabric interconnects so that one of the Nexus 5548s will always be
the root bridge.
C.    Modify the bridge priority on the Nexus 5548s so that one of them will always be the root bridge.
D.    Modify the port priorities on the fabric interconnect uplinks (Paths B and C) so that they are a higher
priority than ports Eth1/4 and Eth1/9 (Path D).
E.    This is an invalid configuration as Cisco UCS fabric interconnects cannot be directly connected.

Answer: C

QUESTION 88
Which of the following Cisco Nexus features is best managed with DCNM-LAN?

A.    VSS
B.    Domain parameters
C.    Virtual switches
D.    AAA

Answer: C

QUESTION 89
Refer to the exhibit. On which of the interfaces can VLANs be configured or modified within this Cisco UCS domain?
A.    VLANs can be configured or modified on all ports.
B.    A, D, E, and F. Ports B and C are automatically configured by the fabric interconnect.
C.    A, E, and F. Ports B, C, and D are automatically configured by the fabric interconnect.
D.    A and F only. No other ports may have their VLAN configurations modified manually.
E.    A only. VLANs are configured on uplinks and are automatically available on any other port with no
configuration necessary.
F.    F only. VLANs are only modified in the service profile.

Answer: D

QUESTION 90
Your company wants Server 1/eth0 (vNIC 1) configured so that it always uses Fabric Interconnect A Port Channel 1 (Po1) when it communicates with anything outside of the Cisco UCS domain. However, if vNIC 1 fails over to Fabric Interconnect B using fabric failover, then vNIC 1 can use any uplink port on Fabric Interconnect B. Which statements are true? (Choose two.)

A.    The fabric interconnects must be in end-host mode.
B.    A pin group must be configured on the server tab in Cisco UCS Manager.
C.    In the service profile for Server 1, vNIC 1 must be explicitly assigned to a pin group.
D.    Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to
a single physical interface and not a port channel because of the LACP load-balancing algorithm.
E.    Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an
uplink on both fabric interconnects or the server is automatically pinned, but not both.

Answer: AC


For those who feel the overwhelming anxiety before their 350-080 exam,Braindump2go Latest updated 350-080 Exam Dumps will help you Pass 100% in a short time preparation! 350-080 Exam Dumps PDF & VCE Full Version Instant Download!

FREE DOWNLOAD: NEW UPDATED 350-080 PDF Dumps & 350-080 VCE Dumps from Braindump2go: http://www.braindump2go.com/350-080.html (394 Q&A)