April/2022 Latest Braindump2go 200-301 Exam Dumps with PDF and VCE Free Updated Today! Following are some new 200-301 Real Exam Questions!

QUESTION 456
What are two characteristics of the distribution layer in a three-tier network architecture? (Choose two.)

A. serves as the network aggregation point
B. provides a boundary between Layer 2 and Layer 3 communications
C. designed to meet continuous, redundant uptime requirements
D. is the backbone for the network topology
E. physical connection point for a LAN printer

Answer: BC

QUESTION 457
What is the purpose of using First Hop Redundancy Protocol in a specific subnet?

A. Filter traffic based on destination IP addressing
B. Sends the default route to the hosts on a network
C. ensures a loop-free physical topology
D. forwards multicast hello messages between routers

Answer: C

QUESTION 458
Which access layer threat-mitigation technique provides security based on identity?

A. Dynamic ARP Inspection
B. using a non-default native VLAN
C. 802.1x
D. DHCP snooping

Answer: C

QUESTION 459
What must be considered when using 802:11 ta?

A. It is compatible with 802 lib- and 802 11-compliant wireless devices
B. It is used in place of 802 11b/g when many nonoverlapping channels are required
C. It is susceptible to interference from 2 4 GHz devices such as microwave ovens.
D. It is chosen over 802 11b/g when a lower-cost solution is necessary

Answer: A

QUESTION 460
When a site-to-site VPN is configured, which IPsec mode provides encapsulation and encryption of the entire original P packet?

A. IPsec tunnel mode with AH
B. IPsec transport mode with AH
C. IPsec tunnel mode with ESP
D. IPsec transport mode with ESP

Answer: C

QUESTION 461
What does physical access control regulate?

A. access to spec fie networks based on business function
B. access to servers to prevent malicious activity
C. access 😮 computer networks and file systems
D. access to networking equipment and facilities

Answer: D

QUESTION 462
On workstations running Microsoft Windows, which protocol provides the default gateway for the device?

A. DHCP
B. STP
C. SNMP
D. DNS

Answer: A

QUESTION 463
How are VLAN hopping attacks mitigated?

A. enable dynamic ARP inspection
B. manually implement trunk ports and disable DTP
C. activate all ports and place in the default VLAN
D. configure extended VLANs

Answer: B

QUESTION 464
What is the role of a firewall in an enterprise network?

A. Forwards packets based on stateless packet inspection
B. Processes unauthorized packets and allows passage to less secure segments of the network
C. determines which packets are allowed to cross from unsecured to secured networks
D. explicitly denies all packets from entering an administrative domain

Answer: C

QUESTION 465
Which two primary drivers support the need for network automation? (Choose two.)

A. Eliminating training needs
B. Increasing reliance on self-diagnostic and self-healing
C. Policy-derived provisioning of resources
D. Providing a ship entry point for resource provisioning
E. Reducing hardware footprint

Answer: CD

QUESTION 466
What is a function of the Cisco DNA Center Overall Health Dashboard?

A. It provides a summary of the top 10 global issues.
B. It provides detailed activity logging for the 10 devices and users on the network.
C. It summarizes the operational status of each wireless devise on the network.
D. It summarizes daily and weekly CPU usage for servers and workstations in the network.

Answer: A

QUESTION 467
Which protocol requires authentication to transfer a backup configuration file from a router to a remote server?

A. DTP
B. FTP
C. SMTP
D. TFTP

Answer: B

QUESTION 468
After installing a new Cisco ISE server, which task must the engineer perform on the Cisco WLC to connect wireless clients on a specific VLAN based on their credentials?

A. Enable the allow AAA Override
B. Enable the Even: Driven RRM.
C. Disable the LAG Mode or Next Reboot.
D. Enable the Authorized MIC APs against auth-list or AAA.

Answer: A

QUESTION 469
Which QoS tool is used to optimize voice traffic on a network that is primarily intended for data traffic?

A. FIFO
B. WFQ
C. PQ
D. WRED

Answer: C

QUESTION 470
Which action does the router take as rt forwards a packet through the network?

A. The router replaces the source and desinaoon labels wth the sending router uterface label as a source and the next hop router label as a desbnabon
B. The router encapsulates the source and destination IP addresses with the sending router P address as the source and the neighbor IP address as the destination
C. The router replaces the original source and destination MAC addresses with the sending router MAC address as the source and neighbor MAC address as the destination
D. The router encapsulates the original packet and then includes a tag that identifies the source router MAC address and transmit transparently to the destination

Answer: C

QUESTION 471
Where is the interface between the control plane and data plane within the software-defined architecture?

A. control layer and the infrastructure layer
B. application layer and the infrastructure layer
C. application layer and the management layer
D. control layer and the application layer

Answer: C

QUESTION 472
An implementer is preparing hardware for virtualization to create virtual machines on a host. What is needed to provide communication between hardware and virtual machines?

A. hypervisor
B. router
C. straight cable
D. switch

Answer: A

QUESTION 473
A network analyst is tasked with configured the date and time on a router using EXEC mode. The date must be set to 12:00am. Which command should be used?

A. Clock timezone
B. Clock summer-time-recurring
C. Clock summer-time date
D. Clock set

Answer: D

QUESTION 474
Refer to the exhibit. If R1 receives a packet destined to 172.161.1, to which IP address does it send the packet?

A. 192.168.12.2
B. 192.168.13.3
C. 192.168.14.4
D. 192.168.15.5

Answer: C

QUESTION 475
A network administrator is asked to configure VLANS 2, 3 and 4 for a new implementation. Some ports must be assigned to the new VLANS with unused remaining. Which action should be taken for the unused ports?

A. configure port in the native VLAN
B. configure ports in a black hole VLAN
C. configure in a nondefault native VLAN
D. configure ports as access ports

Answer: B

QUESTION 476
Refer to the exhibit. Router R4 is dynamically learning the path to the server. If R4 is connected to R1 via OSPF Area 20, to R2 via R2 BGP, and to R3 via EIGRP 777, which path is installed in the routing table of R4?

A. the path through R1, because the OSPF administrative distance is 110
B. the path through R2. because the IBGP administrative distance is 200
C. the path through R2 because the EBGP administrative distance is 20
D. the path through R3. because the EIGRP administrative distance is lower than OSPF and BGP

Answer: C

QUESTION 477
Why was the RFC 1918 address space defined?

A. conserve public IPv4 addressing
B. preserve public IPv6 address space
C. reduce instances of overlapping IP addresses
D. support the NAT protocol

Answer: A

QUESTION 478
Which HTTP status code is returned after a successful REST API request?

A. 200
B. 301
C. 404
D. 500

Answer: A

QUESTION 480
What are network endpoints?

A. act as routers to connect a user to the service prowler network
B. a threat to the network if they are compromised
C. support inter-VLAN connectivity
D. enforce policies for campus-wide traffic going to the internet

Answer: B

QUESTION 481
Refer to the exhibit. Which two prefixes are included in this routing table entry? (Choose two.)

A. 192.168.1.17
B. 192.168.1.61
C. 192.168.1.64
D. 192.168.1.127
E. 192.168.1.254

Answer: BC

QUESTION 482
Which two components are needed to create an Ansible script that configures a VLAN on a switch? (Choose two.)

A. cookbook
B. task
C. playbook
D. model
E. recipe

Answer: CD

QUESTION 483
Which two events occur automatically when a device Is added to Cisco DNA Center? (Choose two. )

A. The device Is assigned to the Global site.
B. The device Is placed into the Unmanaged state.
C. The device Is placed into the Provisioned state.
D. The device Is placed into the Managed state.
E. The device is assigned to the Local site.

Answer: AB

QUESTION 484
Which virtual MAC address is used by VRRP group 1?

A. 0050.0c05.ad81
B. 0007.c061.bc01
C. 0000.5E00.0101
D. 0500.3976.6401

Answer: C

QUESTION 485
Refer to the exhibit. Which two commands, when configured on router R1, fulfill these requirements? (Choose two.)
– Packets towards the entire network 2001:db8:2::/64 must be forwarded through router R2.
– Packets toward host 2001:db8:23::14 preferably must be forwarded through R3.

A. Ipv6 route 2001:db8:23::/128 fd00:12::2
B. Ipv6 route 2001:db8:23::14/128 fd00:13::3
C. Ipv6 route 2001:db8:23::14/64 fd00:12::2
D. Ipv6 route 2001:db8:23::/64 fd00:12::2
E. Ipv6 route 2001:db8:23::14/64 fd00:12::2 200

Answer: DE

QUESTION 486
Refer to the exhibit. When PC-A sends traffic to PC-B, which network component is in charge of receiving the packet from PC-A verifying the IP addresses, and forwarding the packet to PC-B?

A. Layer 2 switch
B. Router
C. Load balancer
D. firewall

Answer: B

QUESTION 487
In software-defined architecture, which place handles switching for traffic through a Cisco router?

A. Control
B. Management
C. Data
D. application

Answer: C

QUESTION 488
Which level of severity must be set to get informational syslogs?

A. alert
B. critical
C. notice
D. debug

Answer: C

QUESTION 489
When a switch receives a frame for a known destination MAC address, how is the frame handed?

A. sent to the port identified for the known MAC address
B. broadcast to all ports
C. forwarded to the first available port
D. flooded to all ports except the one from which it originated

Answer: C

QUESTION 490
How does QoS optimize voice traffic?

A. reducing bandwidth usage
B. by reducing packet loss
C. by differentiating voice and video traffic
D. by increasing jitter

Answer: C

QUESTION 491
What is the function of a controller in controller-based networking?

A. It serves as the centralized management point of an SDN architecture.
B. It centralizes the data plane for the network.
C. It is the card on a core router that maintains all routing decisions for a campus.
D. It is a pair of core routers that maintain all routing decisions for a campus

Answer: A

QUESTION 492
Which action does the router take as it forwards a packet through the network?

A. The router replaces the original source and destination MAC addresses with the sending router MAC address as the source and neighbor MAC address as the destination
B. The router encapsulates the original packet and then includes a tag that identifies the source router MAC address and transmits it transparently to the destination
C. The router encapsulates the source and destination IP addresses with the sending router IP address as the source and the neighbor IP address as the destination
D. The router replaces the source and destination labels with the sending router interface label as a source and the next hop router label as a destination

Answer: C

QUESTION 493
What are two similarities between UTP Cat 5e and Cat 6a cabling? (Choose two.)

A. Both operate at a frequency of 500 MHz.
B. Both support runs of up to 55 meters.
C. Both support runs of up to 100 meters.
D. Both support speeds of at least 1 Gigabit.
E. Both support speeds up to 10 Gigabit.

Answer: CD

QUESTION 494
What is a characteristic of cloud-based network topology?

A. wireless connections provide the sole access method to services
B. onsite network services are provided with physical Layer 2 and Layer 3 components
C. services are provided by a public, private, or hybrid deployment
D. physical workstations are configured to share resources

Answer: A

QUESTION 495
What is the difference in data transmission delivery and reliability between TCP and UDP?

A. TCP transmits data at a higher rate and ensures packet delivery. UDP retransmits lost data to ensure applications receive the data on the remote end.
B. UDP sets up a connection between both devices before transmitting data. TCP uses the three-way handshake to transmit data with a reliable connection.
C. UDP is used for multicast and broadcast communication. TCP is used for unicast communication and transmits data at a higher rate with error checking.
D. TCP requires the connection to be established before transmitting data. UDP transmits data at a higher rate without ensuring packet delivery.

Answer: D

QUESTION 496
How are the switches in a spine-and-leaf topology interconnected?

A. Each leaf switch is connected to one of the spine switches.
B. Each leaf switch is connected to two spine switches, making a loop.
C. Each leaf switch is connected to each spine switch.
D. Each leaf switch is connected to a central leaf switch, then uplinked to a core spine switch.

Answer: B

QUESTION 497
Refer to the exhibit. What is the metric of the route to the 192.168.10.33/28 subnet?

A. 84
B. 110
C. 128
D. 192
E. 193

Answer: E

QUESTION 498
Which two protocols must be disabled to increase security for management connections to a Wireless LAN Controller? (Choose two )

A. Telnet
B. SSH
C. HTTP
D. HTTPS
E. TFTP

Answer: AC

QUESTION 499
What are two benefits of using the PortFast feature? (Choose two )

A. Enabled interfaces are automatically placed in listening state
B. Enabled interfaces come up and move to the forwarding state immediately
C. Enabled interfaces never generate topology change notifications.
D. Enabled interfaces that move to the learning state generate switch topology change notifications
E. Enabled interfaces wait 50 seconds before they move to the forwarding state

Answer: AB

QUESTION 500
Which function is performed by DHCP snooping?

A. propagates VLAN information between switches
B. listens to multicast traffic for packet forwarding
C. provides DDoS mitigation
D. rate-limits certain traffic

Answer: A

QUESTION 501
When a client and server are not on the same physical network, which device is used to forward requests and replies between client and server for DHCP?

A. DHCP relay agent
B. DHCP server
C. DHCPDISCOVER
D. DHCPOFFER

Answer: A

QUESTION 502
Where is the interface between the control plane and data plane within the software-defined architecture?

A. control layer and the infrastructure layer
B. application layer and the infrastructure layer
C. control layer and the application layer
D. application layer and the management layer

Answer: A

QUESTION 503
Which plane is centralized by an SON controller?

A. management-plane
B. control-plane
C. data-plane
D. services-plane

Answer: B

QUESTION 504
An engineer configures interface Gi1/0 on the company PE router to connect to an ISP Neighbor discovery is disabled

Which action is necessary to complete the configuration if the ISP uses third-party network devices?

A. Enable LLDP globally
B. Disable autonegotiation
C. Disable Cisco Discovery Protocol on the interface
D. Enable LLDP-MED on the ISP device

Answer: D

QUESTION 505
What is the benefit of configuring PortFast on an interface?

A. After the cable is connected, the interface uses the fastest speed setting available for that cable type
B. After the cable is connected, the interface is available faster to send and receive user data
C. The frames entering the interface are marked with higher priority and then processed faster by a switch.
D. Real-time voice and video frames entering the interface are processed faster

Answer: B

QUESTION 506
Drag and Drop Question
Drag and drop the DNS lookup components from the left onto the functions on the right.

Answer:

QUESTION 507
Drag and Drop Question
Drag and drop the statement about networking from the left into the Corresponding networking types on the right. Not all statements are used.

Answer:

QUESTION 508
Drag and Drop Question
Drag and drop the IPv6 address type characteristics from the left to the right.

Answer:

QUESTION 509
Drag and Drop Question
An engineer is configuring an encrypted password for the enable command on a router where the local user database has already been configured. Drag and drop the configuration commands from the left into the correct sequence on the right Not all commands are used

Answer:

QUESTION 510
Drag and Drop Question
Drag and drop the functions of DHCP from the left onto any of the positions on the right Not all functions are used.

Answer:

---

Resources From:

1.2022 Latest Braindump2go 200-301 Exam Dumps (PDF & VCE) Free Share:
https://www.braindump2go.com/200-301.html

2.2022 Latest Braindump2go 200-301 PDF and 200-301 VCE Dumps Free Share:
https://drive.google.com/drive/folders/1N579lVwFMNcTo1QgOz_B6__zxBTx36ev?usp=sharing

3.2021 Free Braindump2go 200-301 Exam Questions Download:
https://www.braindump2go.com/free-online-pdf/200-301-PDF-Dumps(631-653).pdf

Free Resources from Braindump2go,We Devoted to Helping You 100% Pass All Exams!